ZD5180高固含聚氨酯面漆 属聚氨酯漆，作面漆使用。广泛用于石化，桥梁，工厂建筑，能源等工业和海洋环境的金属和非金属底材，也可以用在需要装饰的结构。优异的耐侯性能；Excellent resistance to atmospheric exposure conditions；良好的保色保光性能。本页参数：体积固体份 72 ± 3%、干膜厚度 50/75/150 μm、理论涂布率 4.8 m2/L。同品牌同类可对比：脂肪族聚氨酯面漆ZD6430、水性聚氨酯面漆ZD5200、ZD6310-N01F环氧耐油导静电面漆。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 72 ± 3% |
|---|---|
| 干膜厚度 | 50/75/150 μm |
| 理论涂布率 | 4.8 m2/L |
| VOC | ~230(按GB30981-2020 检测) |
| 密度/比重 | 1.43 |
| 组份数 | 双组份 |
| 闪点 | >25℃(混合物) |
| 稀释剂 | 稀释剂ZX-780 |
| 混合比 | 甲(主漆):乙(固化剂)=9.43:1 |
ZD5180 高固态脂肪组聚氨酯面漆
ZD5180 High Solids Polyurethane Finish产品Product Description:
双组份高固态厚膜型脂肪族丙烯酸聚氨酯面漆
Two-component, high solids, high-build aliphatic acrylic polyurethane finish
• 优异的耐侯性能。
• Excellent resistance to atmospheric exposure conditions• 良好的保色保光性能• Good color and gloss retention• 固化温度最低可至摄氏–5℃• Cures at temperatures down to -5℃• 能抗耐矿物油、植物油、松香水、石蜡、脂肪族类石油产品和温和化学品等的溅落类污染。
• Resistant to splash of mineral and vegetable oils, paraffins, aliphatic petroleum productsand mild chemicals• 即使经过较长时间的大气暴晒仍可覆涂后道涂层。
• Can be over coated even after long term atmospheric exposure• 不论无气喷涂,还是刷涂和辊涂都具有良好的涂装施工性能。
• Good application properties by airless, brush and roller• 单道涂层一次涂装即可高达干膜厚度150 微米• High film build-up to 150 μm for one coat• 可直接覆涂在金属底材表面上• Can be applied direct to metal
广泛用于石化,桥梁,工厂建筑,能源等工业和海洋环境的金属和非金属底材,也可以用在需要装饰的结构。
Widely used on ferrous and non- ferrous substrate for chemistry plants, bridges, industryplants, power etc. industry and marine conditions, as well as decoration needed structures.
| 颜色 | 标配颜色和也可按客户要求定制各种颜色。 |
|---|---|
| Color | Standard and customer colors |
| 光泽 | 有光 |
| Gloss | Gloss |
| 体积固体含量 | 72±3% |
| Volume solids | 72±3% |
| 典型混合密度(kg/L)* | 1.43 |
Typical density(kg/L) *:1.43*不同颜色密度会有变化*Density can be various due to color difference
Typical dry film thickness and theoretical spreading rate
| 最低 | 典型 | 最高 | |
| Minimum | Typical | Maximum | |
| 干膜厚度(μm) Dry film thickness(μm) | 50 | 75 | 150 |
| 湿膜厚度(μm) Wet film thickness (μm) | 69 | 104 | 208 |
| 理论涂布率(m2/L)theoretical spreading rate (m2/L) | 14.4 | 9.6 | 4.8 |
| 理论涂布率(m2/kg) Theoretical spreading rate (m2/kg) | 10.1 | 6.71 | 3.56 |
| 实际涂布率 | 允许适当的损耗系数 |
|---|
Practical spreading rate: consider appropriated loss factor
| 出厂VOC 含量(g/l) | ~230(按GB30981-2020 检测) |
|---|
VOC(supplied ,g/L): ~230(follow GB30981-2020)
Application Instruction:
| 适用底材与表面处理 | Suitable Substrate and Treatment. |
|---|
Substrate Condition:
• 裸钢; 喷射清理达到国际标准 ISO 8501-1 的Sa2½级,表面粗糙度满足40 – 70 微米(1.6 – 1.8 密耳), 或者动力工具打磨达到国际标准 ISO 8501-1 的St3 级。
• Steel; blast cleaned to ISO-Sa2½, blasting profile 40 – 70 μm or power tool cleaned toISO-St3
| •确定可以与之兼容配套的前期涂层 | 表面必须洁净干燥,已除尽所有污染物 |
|---|
• Compatible previous coat must be dry and free from any contamination
| 施工和固化条件 | Application and cure condition |
|---|
• 在涂装施工和涂层固化过程中必须确保底材温度至少高于露点温度摄氏 3℃ 以上。
| •Substrate temperature during application and curing should be at least 3℃ | above dew |
|---|
point
| • 在涂装施工和涂层固化过程中可允许接受环境温度低至摄氏-5℃ | ,只要确定底材表面 |
|---|
干燥并无结冰。
| •Substrate temperature during application and curing down to -5℃ | is acceptable; |
|---|
provided the substrate is free from ice and dry• 在涂装施工和涂层固化过程中必须确保环境的相对湿度不超过 85%。
• Relative humidity during application and curing should not exceed 85%• 涂层不可过早接触雨水或在表面结露,否则其颜色和光泽将会受到影响。
• Premature exposure to early condensation and rain may cause color and gloss change
| 混合体积比 | 基料:固化剂 = 7.3 :1 |
|---|
Mixing ration (by volume): A(main): B (curing agent) =7.3:1
| 混合比例(重量比) | 甲(主漆):乙(固化剂)=9.43:1 |
|---|
Mixing ration (by weight): A(main): B (curing agent) =9.43:1• 如有需要,可适量兑稀,但不可超出规定比例,以此将漆料的施工性能调整到理想状态。
• Mixing two components by stirring homogeneous by stirrer to suitable applicationviscosity by adding suitable thinner.
• 过多添加稀释剂通常会导致湿膜的抗流挂性能降低。
• Adding too much thinner results in reduced sag resistance and slower cure• 稀释剂应在两个组份混合后再添加。
• Thinner should be added after mixing the components• 施工必须在适用期内发生。
• Must be applied within pot life once mixed.
| 熟化时间 | 无需熟化 |
|---|---|
| Induction time | No |
Pot life (suitable application viscosity)
| 油漆温度(℃) Paint temperature (℃ ) | 10℃ | 20℃ | 30℃ |
| 适用期(小时) Pot life(hours) | 4 | 3 | 1.5 |
Application methods
有气喷涂
Air Spray
推荐稀释剂 ZX-780;
Recommended Thinner: Thinner ZX-780稀释剂用量10-15% 取决于膜厚要求和施工条件Thinner usage10-15% depending on required thickness and application conditions喷嘴孔径1.0-1.5 毫米Nozzle Size1.0 - 1.5 mm喷涂压力0.3-0.4MPaNozzle pressure0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)无气喷涂Airless Spray
| 推荐稀释剂/清洗剂 | 稀释剂ZX-780 |
|---|
Recommended Thinner/cleaner: Thinner ZX-780稀释剂用量(重量)0 - 10%, 依据所需的漆膜厚度和施工条件而定。
Thinner usage(by weight)0 - 10%, depending on required thickness and application conditions喷嘴孔径约 0.43 – 0.48 毫米 (0.017 – 0.019 英寸) 。
Approx. 0.43 – 0.48 mm (0.017 – 0.019 in)喷嘴压力~20MPaNozzle pressureApprox 20.0 MPa (approx. 200 bar; 2901 p.s.i.)刷涂/辊涂Brush/Roller推荐稀释剂Thinner ZX-780稀释剂用量0-5%Thinner %0-5%
| 清洗剂 | ZX-780 |
|---|---|
| cleaner | Thinner ZX-780 |
| 漆膜厚度和理论涂布率(film thickness and theoretical spreading rate ) | 干膜厚度 | 体积理论涂布率(m2/L) | 重量理论涂布率(m2/kg) |
| Dry film thickness | Theoretical spreading rate by | ||
| volume(m2/L) | weight(m2/kg) | ||
50 微米
14.4 10.10
50(μm)
| 75 微米 | 9.6 6.71 |
|---|
| 75(μm) 100 微米 100(μm) | 75(μm) 7.2 | 75(μm) 5.03 |
| 150 微米 150(μm) | 4.8 | 3.56 |
Over coating interval(@75μm DFT)
| 自身和相容的面漆 (self and compatible finishes) ) | 表面温度 最短覆涂间隔时间(小时) Minimum over coating interval(hours) | -5℃ 24 | 0℃ 18 | 10℃ 10 | 20℃ 8 | 30℃ 4 | 40℃ 2 |
| 最长覆涂间隔时间 Maximum over coating interval | 无限期,但是必须表面干净和无任何污染物 No limit, but surface should be clean and free of any contaminants. | ||||||
注:以上数据都是在通风状况良好、典型膜厚、相对湿度≤75%的条件下测得数据,仅供参考。实际干燥时间及覆涂前的时间间隔可长可短,取决于漆膜厚度、通风状况、湿度、下层油漆、提前装卸需求和机械强度等因素的影响。涂层完全固化后,才能处于浸渍环境但是只是适合短期或飞溅。
above are typical data based on good ventilation, typical film thickness and relativehumidity≤ 75%, just for reference only.
Real drying time base on impact of over coating interval, film thickness, ventilation, humidity,undercoat, ahead of loading and unloading and mechanical requirement etc. Immersiononly allowed after full cure but only for short term or splashing.
干燥/固化时间(干膜75 微米)
Drying/curing table (@75 ㎛DFT)
| 底材温度 | 表干(小时) | 实干(小时) | 完全固化(天) |
| Substrate | Surface dry(hrs) | Dry to handle(hrs) | Full cure time(days) |
temperature
| -5℃ | 20 | 36 | 20 |
| 0℃ | 12 | 24 | 14 |
| 10℃ | 4 | 18 | 9 |
| 20℃ | 2 | 10 | 7 |
| 30℃ | 1 | 4 | 3 |
| 40℃ | 1 | 3 | 2 |
| 前道油漆 | 各种环氧、聚氨酯中层漆或防锈底漆, |
|---|
| Previous coat | direct to blasted Sa2.5 steel or power tool to St3, various epoxies,polyurethane mid-coats or anti-corrosive primers. |
|---|---|
| 后道油漆 | 各种相容的面漆 |
| Next coat | self or various compatible finishes. |
具体向无锡华东锌盾公司咨询
For details, please consult ZINDN company.
Notification;
必须使用规定的稀释剂,并涂覆于配套的底漆或中间漆上,否则会影响产品质量。
Must use be used approved thinner, and over-coated on systemic mid-coats or primers,在配漆过程中,严禁与水,酸、碱、醇等接触。乙组份极易与水、醇等物质反应,配漆后余下的乙组份的包装桶必须盖严Paint preparation should strictly forbid to contact water, acid, alkali, alcohol etc. The cureagent will react with water etc., the left of paint of cure agent has to be well sealed.
施工及干燥固化期间,相对湿度不得大于80%。
The relative humidity should be no more than 85% when application and curing process.
涂装过程中,或在刚涂装完不久,表面遭受到水汽冷凝、突然降温,会使表面失去光泽、发白、质量变差。
The appearance will lose gloss, whiten and turn to bad quality once the condensation,sudden temperature drop happened.
采用辊涂和刷涂时,要获得完全遮盖效果,可能需涂覆多道,尤其是对于某些无铅的鲜艳颜色,如黄色、橙色等等。
Muti coats is needed to achieve enough hiding power with brush and roller application,particular for non-chromatic color pigments like organic yellow, orange etc.
选用特别的浅色,如亮黄,亮橙色时,下面涂层需要选用接近或者尽量的浅色。
When choosing bright colors such as bright yellow, bright orange etc., the undercoat shouldbe similar or lighter colors to achieve enough hiding power.
Package, Storage and Shelf life
package size
| 组份 components | A(主料) | B(固化剂) |
| 包装桶规格 Container size | 20 升 | 3 升 |
| 包装量(重量) Package size(weight) | 21.7 公斤 | 2.3 公斤 |
| 包装量(体积) Package size (volume) | ~14.7 升 | ~2 升 |
| 闪点 | >25℃(混合物) |
|---|---|
| Flash Point | >25℃(Mixed) |
| 储存条件 | 须按照国家规定储存。储存环境应干燥、阴凉、通风良好并避开热源和火源。包装容器必须保持密闭。 |
Storage condition:must follow national rules. Should be dry, cool, good ventilation andaway heat and fire. The container should be well sealed.
| 储存有效期 | 良好储存条件下的储存有效期为1 年。 |
|---|---|
| Shelf life | 1 year at good storage condition. |
Health, Safety and Environment本品含有易燃物,施工现场安全应符合有关国家或当地政府规定。请注意包装上的安全标签并阅读产品安全数据手册(MSDS)。
避免吸入溶剂蒸气和漆雾,避免油漆接触皮肤和眼睛,严禁吞服本产品,采取必要的预防和防护措施防火、防爆和保护环境。需在通风良好的情况下使用本品。在狭窄处或空气不流通处施工,必须提供强力通风。
废弃物处理必须符合有关国家或当地政府规定。
This product contains flammable components; the application site has to meet nationalsafety and local government requirement. More details please read and follow materialsafety data sheet (MSDS)Avoid solvent vapor and paint mist, avoid contacting skin and eyes, forbidden swallowing,
| must | have necessary to have prevention and protection for fire, exploration andenvironment protection solutions. Application under good ventilation, provide sufficientventilation when in narrow space and in non-good air flow. |
|---|
Waste treatment has to follow national and local government requirement.
本产品资料及数据是根据我们的试验和实际使用中的经验而积累的,可作为施工指南,但由于产品的使用通常在我们的控制范围之外,所以我们只提供产品本身质量的保证。我公司保DeclareThe product documents and data based our experiments and application experience, usefor application instruction. The application condition is usually out of our control; we onlywarrant product quality itself. ZINDN keeps the authority to modify for improvement withoutpre-notification to customers.
| 版本信息 | 修改于2025 年7 月,本说明书取代以前的版本,如有其它语言,最终以中文为准。 |
|---|---|
| Version | Revised in July 2025, this version is instead of previous version. The otherlanguages are subjected to Chinese technical data sheet锌盾商标,及锌盾相关的标识,是锌盾集团所有的财产,未经许可,任何个人和组织无权使用。 |
The ZINDN Logo,and ZINDN remarks are properties of group of companies, all thirdparties are not allowed to use without permit.
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 锌盾 ZINDN ZD5180高固含聚氨酯面漆 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
