SILIFEND ZINC AS-50 自干型无机富锌涂料RECOMMENDED USE 属富锌底漆，无机硅酸锌漆体系。Compatible with Anti-Slip friction surface of bridge。烷基硅酸酯为基料的自干型无机富锌涂料。本页参数：体积固体份 57% ± 2%、干膜厚度 40-160 微米/道、理论涂布率 8.1 平方米/升。同品牌同类可对比：SD ZINC 2000 无机富锌底漆2000、SD ZINC 1000HA 无机硅酸锌车间底漆1000HA、SILISAFE ZINC 80 水性无机富锌底漆80。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 57% ± 2% |
|---|---|
| 干膜厚度 | 40-160 微米/道 |
| 理论涂布率 | 8.1 平方米/升 /70 微米 |
| VOC | 378 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 密度/比重 | — |
| 组份数 | — |
| 闪点 | 18℃以上 |
| 稀释剂 | 专用稀释剂 |
| 混合比 | 液体粉末=1/5(重量比) |
| SILIFEND ZINC AS-50 | 无机富锌防滑漆AS-50 |
|---|
A self-curing inorganic zinc coating based on alkyl silicate binder
烷基硅酸酯为基料的自干型无机富锌涂料
Compatible with Anti-Slip friction surface of bridge
适用于桥梁防滑摩擦面
Complies with JT/T 722-2008
符合公路桥梁钢结构防腐涂装技术条件JT/T 722-2008
Remarkable corrosion resistance
极好的防腐性能
Outstanding resistance to impact, mechanical abrasion and organic solvent
优良的耐冲击、耐磨损和耐有机溶剂性能
Excellent initial hardness
极好的初始硬度
High-build applicability
极好的厚涂施工性能
Remarkable heat resistance and less scorch by heat treatment
优良的耐热性,热处理烧损少
| Color | Grey |
|---|---|
| 颜色 | 灰色 |
| Volume Solids 体积固体份 | 57%±2% |
| VOC | 378g/L,accord with EU Dircrtive2004/42/EC, subcategory j |
| 挥发性有机化合物含量 | 378 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| Flash Point | Greater than 18℃ |
| 闪点 | 18℃以上 |
| Film thickness | Dry : 40-160μm/coat Wet : 70-280μm/coat |
| 涂装膜厚 | 干膜: 40-160 微米/道湿膜: 70-280 微米/道 |
| Theoretical Coverage | 8.1m2/L/70μm |
| 理论涂布率 | 8.1 平方米/升/70 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理,外界环境,施工方法等多种因素有关
| Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Add powder to liquid first, then mix thoroughly with power agitator |
| 混合 | 将粉末加入液体,使用动力工具搅拌均匀 |
| Mixing Ratio | Liquid/Powder=1/5(by weight) |
| 混合比例 | 液体粉末=1/5(重量比) |
| Pot Life | 5℃ | 10℃ | 20℃ | 30℃ |
| 混合使用期 | 8hrs | 6hrs | 4hrs | 3hrs |
| Application Methods | Airless spray, air spray |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂 |
Airless spray 无气喷涂
| Nozzle tip | 喷嘴尺寸 | 0.43mm-0.53mm |
| Nozzle pressure | 出口压力 | ≥10MPa |
| Thinning ratio | 稀释比率 | 0-10% by volume(体积比) |
| Thinner | SD Zinc Primer Thinner |
|---|---|
| 稀释剂 | 专用稀释剂 |
| Drying time & | Temperature | 温度 | 5℃ | 10℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 60mins | 30mins | 20mins | |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 12hrs | 6hrs | 4hrs | 1hr |
| Min. interval | 最小涂装间隔 | 96hrs | 72hrs | 48hrs | 24hrs | |
| Max. interval | 最大涂装间隔 | - | ||||
| Applied Substrate | Bare steel |
|---|---|
| 适用底材 | 裸钢 |
| Typical topcoat | Epomarine Primer, Epotect EX (M), Uuiversal EP-60 or according to the coating |
| 适用上涂 | system of COSCO Kansai. |
环氧底漆、环氧云铁厚浆漆EX(M)、环氧漆EP-60 或参考我司推荐涂装配套
Store in dry, cool condition and away from sources of heat and ignition. Containers
must be kept tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 6 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起6 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the
time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development. Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非 我方所能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司 产品及生产工艺的不断发展,本说明书的内容也会随时进行更改,此中所有信息 均以我方确认为主。产品使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | 2015/01 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI SILIFEND ZINC AS-50 自干型无机富锌涂料RECOMMENDED USE 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
