EPOTECT PC 100PH 属环氧漆。primer. For use under insulation for pipe . 用于新建设施或作为维修养底漆使用，推荐用于管道保温层下。是一种双组份高固体厚浆型环氧酚醛涂料。本页参数：体积固体份 66 ± 2%、干膜厚度 100-150 微米/道、理论涂布率 0.230 千克/平方米/100 微米。同品牌同类可对比：TANKCARE AE-50 酚醛环氧导静电漆AE-50、TANKCARE PC-30 酚醛环氧漆PC-30、TANKCARE PC-50 酚醛环氧漆PC-50。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 66 ± 2% |
|---|---|
| 干膜厚度 | 100-150 微米/道 |
| 理论涂布率 | 0.230 千克/平方米 /100 微米 |
| VOC | 332g/L,符合欧盟溶剂排放指令2004/42/EC,j子类别 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 20℃以上 |
| 稀释剂 | 环氧稀释剂20# |
| 混合比 | Base/Hardener=9/1(by weight) |
| EPOTECT PC 100PH | 酚醛环氧漆PC 100PH |
|---|
A two pack high solids hi-build epoxy novolac coating.
是一种双组份高固体厚浆型环氧酚醛涂料。
As a primer can be used in new construction situations and as industrial maintenance
primer. For use under insulation for pipe .
用于新建设施或作为维修养底漆使用,推荐用于管道保温层下。
Complies with SH/T3022-2011
符合行业标准SH/T3022-2011,《石油化工设备和管道涂料防腐蚀设计规范》
Good anti-corrosive performance
优秀的防腐性能
Excellent surface-tolerant properties
极好的表面适应性能
Suitable for high temperature(up to 200℃)
用于高温部位(达到200℃)
Good applicability
良好的施工性
| Color | Grey and oxide red |
|---|---|
| 颜色 | 灰色,铁红色 |
| Volume Solids 体积固体份 | 66±2 % |
| VOC | 332g/L, accord with EU Dircrtive2004/42/EC, subcategory j |
| 挥发性有机化合物含量 | 332g/L,符合欧盟溶剂排放指令2004/42/EC,j子类别 |
| Flash Point | Greater than 20℃ |
| 闪点 | 20℃以上 |
| Film thickness | Dry :100-150 microns/coat Wet : 150-227microns/coat |
| 涂装膜厚 | 干膜:100-150 微米/道湿膜:150-227 微米/道 |
| Theoretical Coverage | 0.230kg/m²/100 microns |
| 理论涂布率 | 0.230 千克/平方米/100 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂布率与表面处理, 外界环境, 施工方法等多种因素有关。
| Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=9/1(by weight) |
| 混合比例 | 主剂/固化剂=9/1(重量比) |
| Pot Life | 10℃ | 20℃ | 30℃ |
| 混合使用期 | 8hrs | 5hrs | 2.5hrs |
| Application Methods | Airless spray, air spray, brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂、滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | Graco 417、517 |
| Nozzle pressure | 出口压力 | ≥10Mpa |
| Thinning ratio | 稀释比率 | 5-15% by weight(重量比) |
| Thinner | Epomarine Thinner 20# |
|---|---|
| 稀释剂 | 环氧稀释剂20# |
| Drying time & | Temperature | 温度 | 5℃ | 10℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 6hrs | 3hrs | 1hrs | 0.5hrs |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 30hrs | 24hrs | 16hrs | 12hrs |
| Min. interval | 最小涂装间隔 | 30hrs | 24hrs | 16hrs | 12hrs | |
| Max. interval | 最大涂装间隔 | 7days | ||||
| Applied Substrate | Bare steel |
|---|---|
| 适用底材 | 裸钢 |
| Preceding coat | SD Zinc 500, or according to the coating systems of Kansai. |
| 适用下涂 | SD Zinc 500, 或参考我司推荐配套。 |
| Typical topcoat | Epomarine EX-500, PU FINISH HD-50 or according to the coating system of Cosco |
| 适用上涂 | Kansai. |
各类环氧中涂、聚氨酯面漆或参考我司涂装配套
Store in dry, cool condition and away from sources of heat and ignition. Containers
must be kept tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at
the time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件 非我方所能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我 公司产品及生产工艺的不断发展,本说明书的内容也会随时进行更改,此中所 有信息均以我方确认为主。产品使用前,请确认所持说明书为最新版本。
| Issued Date | 2019/11/5 |
|---|---|
| 发行日期 | 2019/11/5 |
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI EPOTECT PC 100PH 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
