EPOTECT GX 防锈底漆 属环氧漆，作底漆使用。对镀锌钢材、轻金属表面起保护作用。由环氧树脂、胺加成物及特殊添加剂组成的防锈底漆。与轻金属、镀锌钢材有极好的附着力 Excellent durability in chemical and marine environment 极好的耐化性和海洋环境适应性 Good applicability 良好的施工性 Provides hardness, abrasion resistance 硬度好、耐磨损。本页参数：体积固体份 56% ± 2%、干膜厚度 50-100 微米/道、理论涂布率 11.2 平方米/升。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 56% ± 2% |
|---|---|
| 干膜厚度 | 50-100 微米/道 |
| 理论涂布率 | 11.2 平方米/升 /50 微米 |
| VOC | 406/克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 21℃以上 |
| 稀释剂 | 环氧稀释剂20# |
| 混合比 | Base/Hardener=9/1(by weight) |
| EPOTECT GX | 环氧漆GX |
|---|
A rust preventive primer based on epoxy resin, amine adduct and special additives
由环氧树脂、胺加成物及特殊添加剂组成的防锈底漆。
For the protection of galvanized steel or light metal surfaces.
对镀锌钢材、轻金属表面起保护作用。
Excellent adhesion to light metal and galvanized steel
与轻金属、镀锌钢材有极好的附着力
Excellent durability in chemical and marine environment
极好的耐化性和海洋环境适应性
Good applicability
良好的施工性
Provides hardness, abrasion resistance
硬度好、耐磨损
| Color | Grey |
|---|---|
| 颜色 | 灰色 |
| Volume Solids 体积固体份 | 56%±2% |
| VOC | 406g/L, accord with EU Dircrtive2004/42/EC,subcategory j |
| 挥发性有机化合物含量 | 406/克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| Flash Point | Greater than 21℃ |
| 闪点 | 21℃以上 |
| Film thickness | Dry : 50-100 μm/coat Wet : 90-180μm/coat |
| 涂装膜厚 | 干膜: 50-100 微米/道湿膜: 90-180 微米/道 |
| Theoretical Coverage | 11.2 m2/Ltr/50 microns |
| 理论涂布率 | 11.2 平方米/升/50 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理,外界环境,施工方法等多种因素有关
| Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=9/1(by weight) |
| 混合比例 | 主剂/固化剂=9/1(重量比) |
| Pot Life | 5℃ | 20℃ | 30℃ |
| 混合使用期 | 16hrs | 6.5hrs | 4hrs |
| Application Methods | Airless spray, air spray brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂和滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | 0.33mm-0.43mm |
| Nozzle pressure | 出口压力 | ≥10Mpa |
| Thinning ratio | 稀释比率 | 0-5% by volume(体积比) |
Brush/Roller 刷涂/滚涂 Thinning ratio 稀释比率 0-10% by volume(体积比)
| Thinner | Epomarine Thinner 20# |
|---|---|
| 稀释剂 | 环氧稀释剂20# |
| Drying time & | Temperature | 温度 | 5℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 0.5hrs | 0.3hrs | 0.2hrs |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 3.5hrs | 2hrs | |
| Min. interval | 最小涂装间隔 | 48hrs | 24hrs | 16hrs | |
| Max. interval | 最大涂装间隔 | 7days | |||
| Applied Substrate | Galvanized steel and light metal etc. |
|---|---|
| 适用底材 | 镀锌材,轻金属等 |
| Typical topcoat | Epotect EX, PU Finish HS-50, PU Finish 2010, Flon Finish HS-50 or according to the |
| 适用上涂 | coating system of Cosco Kansai. |
环氧漆Epotect EX、聚氨酯面漆HS-50、聚氨酯面漆2010、氟碳面漆HS-50 或参 考我司涂装配套
The information given on this sheet is to the best of our knowledge and accurate at the
time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development. Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非 我方所能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司 产品及生产工艺的不断发展,本说明书的内容也会随时进行更改,此中所有信息 均以我方确认为主。产品使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | 2019/04 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI EPOTECT GX 防锈底漆 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
