EPOFEND GLASS 30 环氧玻璃鳞片漆30 属玻璃鳞片漆，环氧漆体系。也可用于原油储罐内壁涂料配套中。是一种采用玻璃鳞片加强的厚涂型双组份环氧涂料。极好的耐酸、耐碱、耐油和耐海水性 Prevent penetration of chemicals and water steam 能防止水汽或化学气体侵入 Excellent mechanical strength and excellent adhesion property 很强的机械性和附着力。本页参数：体积固体份 80 ± 2%、干膜厚度 125-500 微米/道、理论涂布率 4.0 平方米/升。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 80 ± 2% |
|---|---|
| 干膜厚度 | 125-500 微米/道 |
| 理论涂布率 | 4.0 平方米/升 /200μm |
| VOC | 196 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 30℃以上 |
| 稀释剂 | 环氧稀释剂20# |
| 混合比 | Base/Hardener=5.2/1(by weight) |
| EPOFEND GLASS 30 | 环氧玻璃鳞片漆30 |
|---|
A high build, two packs epoxy coating reinforced with Glass flakes.
是一种采用玻璃鳞片加强的厚涂型双组份环氧涂料
For surface subject to abrasion and highly corrosive environment of splash zones, jetty
pilings and working decks. Can be used as interior lining for crude oil tanks.
用在严重腐蚀环境和经常受到磨损的表面,如浪溅带、防波堤和甲板。也可用于 原油储罐内壁涂料配套中
Complies with JT/T 722-2008, GB/T 28699-2012, SY/T 0457-2010
符合公路桥梁钢结构防腐涂装技术条件JT/T 722-2008、钢结构防护涂装通用技术 条件GB/T 28699-2012、钢制管道液体环氧涂料内防腐层技术标准SY/T 0457-2010
Excellent durability against acid, alkali, oils, sea water
极好的耐酸、耐碱、耐油和耐海水性
Prevent penetration of chemicals and water steam
能防止水汽或化学气体侵入
Excellent mechanical strength and excellent adhesion property
很强的机械性和附着力
| Color | Grey |
|---|---|
| 颜色 Volume Solids | 灰色 |
| 体积固体份 | 80±2% |
| VOC | 196g/L,accord with EU Dircrtive2004/42/EC,subcategory j. |
| 挥发性有机化合物含量 | 196 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| Flash Point | Greater than 30℃ |
| 闪点 | 30℃以上 |
| Film thickness | Dry : 125-500 μm/coat Wet : 155-625μm/coat |
| 涂装膜厚 | 干膜: 125-500 微米/道湿膜: 155-625 微米/道 |
| Theoretical Coverage | 4.0m2/Ltr/200 microns |
| 理论涂布率 | 4.0 平方米/升/200μm |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理,外界环境,施工方法等多种因素有关
| Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=5.2/1(by weight) |
| 混合比例 | 主剂/固化剂=5.2/1(重量比) |
| Pot Life | 5℃ | 10℃ | 20℃ | 30℃ |
| 混合使用期 | 4hrs | 3.5hrs | 3hrs | 2.5hrs |
| Application Methods | Airless spray, air spray brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂和滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | 0.027-0.033(in) |
| Nozzle pressure | 出口压力 | ≥15MPa |
| Thinning ratio | 稀释比率 | 5-20% by volume(体积比) |
Brush/Roller 刷涂/滚涂 Thinning ratio 稀释比率 5-20% by volume(体积比)
| Thinner | Epomarine Thinner 20# |
|---|---|
| 稀释剂 | 环氧稀释剂20# |
| Drying time & | Temperature | 温度 | 5℃ | 10℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 10hrs | 6hr | 4hr | 3hr |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 48hrs | 36hrs | 24hrs | 18hrs |
| Min. interval | 最小涂装间隔 | 36hrs | 24hrs | 18hrs | ||
| Max. interval | 最大涂装间隔 | 9days | 7days | |||
| Applied Substrate | Bare steel |
|---|---|
| 适用底材 | 裸钢 |
| Typical topcoat | PU Finish HS-50, PU Finish 2010 or according to the coating system of COSCO |
| 适用上涂 | Kansai. |
聚氨酯面漆HS-50、聚氨酯面漆2010 或参考中远关西涂装配套
Store in dry, cool condition and away from sources of heat and ignition. Containers
must be kept tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the
time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development. Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非 我方所能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司 产品及生产工艺的不断发展,本说明书的内容也会随时进行更改,此中所有信息 均以我方确认为主。产品使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | 2018/1 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI EPOFEND GLASS 30 环氧玻璃鳞片漆30 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
