1st Buff color is characterized by Self Indicating (SI) technology, which enables a painter to visually judge if the correct film thickness (wet dry) has been achieved during the application process and。本页参数：体积固体份 65 ± 2%、干膜厚度 125-300 μm、理论涂布率 5.20 m²/L。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 65 ± 2% |
|---|---|
| 干膜厚度 | 125-300 μm |
| 理论涂布率 | 5.20 m²/L (125 μm) |
| VOC | 321 g / L as supplied |
| 密度/比重 | — |
| 组份数 | — |
| 稀释剂 | NIPPON MARINE THINNER 600 / NIPPON … |
| 混合比 | BASE 3.57 / HARDENER 1 |
| 颜色/外观 | 1st coat : Buff |
本型号原厂说明书未标注涂层位置与树脂类型，暂未归入上述分类；可按分类浏览同类产品，或联系我们确认配套体系。
| A two-pack pure epoxy designed for petroleum and chemical product tanks. | It offers superior resistance to petroleum products, solvents, water and chemical attack. |
|---|
1st Buff color is characterized by Self Indicating (SI) technology, which enables a painter to visually judge if the correct film thickness (wet / dry) has been achieved during the application process and
| after the completion of painting. | Two coat system with SI paint (1st coat) plus non-SI paint (2nd coat) is recommended. |
|---|
Product Carriers, Tanks for petroleum products
| Type | Pure epoxy (Two-pack) |
|---|---|
| Color | 1st coat : Buff |
| 2nd coat | Gray (Non-SI) |
| Gloss | Semi-gloss |
| Volume Solids | 65 ± 2% (ISO3233:1998) |
| Dry Film Thickness | 125 ~ 300 μm |
| Approx. Wet Film Thickness | 192 ~ 462 μm |
| Theoretical Coverage | 5.20 m² / L (125 μm) |
| Drying Time | Surface Dry | 31/2 hours(5℃) | 11/2 hours(20℃) | 40 minutes (30℃) |
| Dry Hard | 36 hours (5℃) | 16 hours (20℃) | 10 hours (30℃) | |
| Interval before Overcoating | Min. | 36 hours (5℃) | 16 hours (20℃) | 10 hours (30℃) |
| ( by self ) | Max. | 10 days (5℃) | 7 days (20℃) | 5 days (30℃) |
| VOC Values | 321 g / L as supplied |
|---|---|
| Thinner | NIPPON MARINE THINNER 600 / NIPPON MARINE THINNER 615 (China Regions) |
Airless Spray
| Tip range | 0.48 ~ 0.53 mm |
|---|---|
| Fan angle | 45 ~ 60° |
| ( T/U ) | 30° Output pressure 150 ~ 200 kg / cm² |
| Brush | For touching up small areas only |
| Mixing Ratio by Volume | BASE 3.57 / HARDENER 1 |
| Pot Life after Mixing | 5 hours (5℃) |
| 3 hours (20℃) | 21/2 hours (30℃) |
| Packaging | Two Packs Package may vary from country to country. |
| Japan Local Brand | NIPPE EPOXY PC NOA |
| Flash Point | BASE 34 ℃, HARDENER 25 ℃ |
Blast cleaned to ISO-Sa 21/2
is recommended.
Take precautions to avoid skin and eye contact (i.e. gloves, goggles, face masks, barrier creams etc.) Proper ventilation and protective measures must be provided during applications and drying period to keep solvent vapor concentrations within safe limits.
Prior to use, obtain, consult and follow the SDS for this product concerning health and safety information.
1)The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.
2)Apply this paint immediately after sandblasting. Before painting, the areas where corroded, welded and burnt should be carefully treated with sandblasting,shotblasting,or a disc sander or a power brush.
3)If half-dried painted surface is subjected to rain or dew, blooming or sweating may occur, with the surface turned to white. Rub the area lightly with a wire brush before painting.
4)For the applications, refer to our "Suitability Table of Cargoes for Loading" and "Application Manual of NOA PC System".
5) For availability of product consult Nippon Paint Marine representatives.
6) Unit size and filled volumes can vary due to local regulations.
7) Store the paints in paint store.
8) Use products that comply with local regulations to clean the paint equipment.
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 立邦船舶 NIPPON MARINE NOA PC 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
