depending on dry film thickness (DFT) requirement and application area.本页参数：体积固体份 58 ± 2%、干膜厚度 75-100 μm、理论涂布率 7.73 m²/L。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 58 ± 2% |
|---|---|
| 干膜厚度 | 75-100 μm |
| 理论涂布率 | 7.73 m²/L (75 μm) |
| VOC | 470 g / L as supplied |
| 密度/比重 | — |
| 组份数 | — |
| 稀释剂 | NIPPON MARINE THINNER 615 |
| 混合比 | BASE 5.5 / HARDENER 1 |
| 颜色/外观 | 445 Red oxide, 060 Gray, 442 Green,… |
本型号原厂说明书未标注涂层位置与树脂类型，暂未归入上述分类；可按分类浏览同类产品，或联系我们确认配套体系。
A flexible, surface-tolerant epoxy paint that is used for general onboard maintenance, touch up and repair work on exposed decks, exterior of superstructure, topsides, hatch covers, cargo holds and etc.
E-MARINE MAX provides both anticorrosive properties and a finish. It can be used as a primer and finish coat or as a single coat system; depending on dry film thickness (DFT) requirement and application area.
Easy application with a brush or roller.
Anticorrosive for decks, holds, superstructures, etc.
| Type | Epoxy (Abrasion resistant / High build)(Two-pack) |
|---|---|
| Color | 445 Red oxide, 060 Gray, 442 Green, 000 White |
| Gloss | Flat |
| Volume Solids | 58 ± 2% (ISO3233:1998) |
| Typical Dry Film Thickness | 75 ~ 100 μm |
| Approx. Wet Film Thickness | 134 ~ 179 μm |
| Theoretical Coverage | 7.73 m²/ L (75 μm) |
(5℃) 2.5 hours (20℃)
| Drying Time | Surface Dry | 6 hours | 40 minutes (30℃) | |
| Dry Hard | 8 hours (5℃) | 4 hours (20℃) | 2 hours (30℃) | |
| Interval before Overcoating | Min. | 12 hours (5℃) | 5 hours (20℃) | 3 hours (30℃) |
| ( by self ) | Max. | 30 days (5℃) | 30 days (20℃) | 30 days (30℃) |
| VOC Values | 470 g / L as supplied |
|---|---|
| Thinner | NIPPON MARINE THINNER 615 |
Brush / Roller Suitable
| Airless Spray | Applicable |
|---|---|
| Tip range | 0.48 mm |
| Fan angle | 55 ~ 62° |
| Output pressure | 100 ~ 150 kg / cm² |
| Mixing Ratio by Volume | BASE 5.5 / HARDENER 1 |
| Pot Life after Mixing | 5 hours (5℃) 3 hours (20℃) 1.5 hour (30℃) |
| Package | Two Packs - 16L (BASE 13.5L, HARDENER 2.5L) |
| Flash Point | BASE 22 ℃, HARDENER 25 ℃ |
All surfaces to be coated should be clean, dry and free from contamination.
High pressure fresh water wash and remove all oil / grease, soluble contaminants and other foreign matters.
Take precautions to avoid skin and eye contact (i.e. gloves, goggles, face masks, barrier creams etc.) Proper ventilation and protective measures must be provided during applications and drying period to keep solvent vapor concentrations within safe limits.
Prior to use, obtain, consult and follow the SDS for this product concerning health and safety information.
| 1) | The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development. |
|---|---|
| 2) | At temperatures below 5℃, the coating will take longer to dry and harden. |
| 3) | For availability of product consult Nippon Paint Marine representatives. |
| 4) | Unit size and filled volumes can vary due to local regulations. |
| 5) | Store the paints in paint store. |
| 6) | Some regions will be supplied with NIPPON MARINE THINNER 600 instead of NIPPON MARINE THINNER 615. |
| 7) | Use products that comply with local regulations to clean the paint equipment. |
| 8) | The Application Guide offers product details and recommended practices for the use of the product. |
| 9) | Refer to Nippon Paint Marine Global Colour Cards and contact local Nippon Paint Marine representative for colour availability & customisation. |
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 立邦船舶 NIPPON MARINE NIPPON E-MARINE MAX 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
