A/CⅡM A two-pack epoxy tie-coat anticorrosive designed especially for maintenance & repair application at Dry Dock. The combination with effective anti-corrosive primers, the system provides excellent seawater resistance and good adhesion property to various kinds of antifoulings and finishes with optimized overcoating intervals.本页参数：体积固体份 63 ± 2%、干膜厚度 50-125 μm、理论涂布率 8.42 m²/L。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 63 ± 2% |
|---|---|
| 干膜厚度 | 50-125 μm |
| 理论涂布率 | 8.42 m²/L (75 μm) |
| VOC | 371 g / L |
| 密度/比重 | — |
| 组份数 | — |
| 稀释剂 | NIPPON MARINE THINNER 615 |
| 混合比 | BASE 7 / HARDENER 1 |
| 颜色/外观 | Grey |
本型号原厂说明书未标注涂层位置与树脂类型，暂未归入上述分类；可按分类浏览同类产品，或联系我们确认配套体系。
| NIPPON | E-MARINE |
|---|
A/CⅡM A two-pack epoxy tie-coat anticorrosive designed especially for maintenance & repair application at Dry Dock. The combination with effective anti-corrosive primers, the system provides excellent seawater resistance and good adhesion property to various kinds of antifoulings and finishes with optimized overcoating intervals.
For Maintenance & repair as at Dry Dock As Tie-coat anticorrosive for outer hull (including boottop and topsides), decks, superstructure, etc.
| Type | Epoxy (Two-pack / High build) |
|---|---|
| Color | Grey |
| Gloss | Flat |
| Volume Solids | 63 ± 2% (ISO3233:1998) |
| Typical Dry Film Thickness | 50 ~ 125 μm |
| Approx. Wet Film Thickness | 79 ~ 198 μm |
| Theoretical Coverage | 8.42 m²/L (75 μm) |
as supplied
| Drying Time | Surface Dry | 5 hours (5℃) | 2 hours (20℃) | 1 hour (30℃) |
| Dry Hard | 24 hours (5℃) | 14 hours (20℃) | 10 hours (30℃) | |
| Interval before Overcoating | Min. | 5 hours (5℃) | 3 hours (20℃) | 2 hours (30℃) |
| (by self) | Max. | - (5℃) | - (20℃) | - (30℃) |
| VOC Values | 371 g / L |
| Thinner | NIPPON MARINE THINNER 615 |
|---|
Airless Spray
| Tip range | 0.48 ~ 0.59 mm |
|---|---|
| Fan angle | 55° ~ 62° |
| (For T/U) | 30° |
| Output pressure | 150 ~ 200 kg/cm² |
| Brush | For touching up small areas only |
| Mixing Ratio by Volume | BASE 7 / HARDENER 1 |
| Pot Life after Mixing | 6 hours (5℃) |
| 3 hours (20℃) | 2 hours (30℃) |
| Packaging | Two Packs - 20L (base 17.5L, HARDENER 2.5L) |
| Flash Point | BASE 24℃, HARDENER 42℃ |
All surfaces to be coated should be clean, dry and free from contamination.
High pressure fresh water wash and remove all oil / grease, soluble contaminants and other foreign matters.
Take precautions to avoid skin and eye contact (i.e. gloves, goggles, face masks, barrier creams etc.) Proper ventilation and protective measures must be provided during applications and drying period to keep solvent vapor concentrations within safe limits.
Prior to use, obtain, consult and follow the SDS for this product concerning health and safety information.
1)The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.
2)Prior to overcoating, remove heavily chalked layer, salt contamination, etc. by fresh water washing.
3) For availability of product consult Nippon Paint Marine representatives.
4) Unit size and filled volumes can vary due to local regulations.
5) Store the paints in paint store.
6) Use products that comply with local regulations to clean the paint equipment.
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 立邦船舶 NIPPON MARINE NIPPON E-MARINE A/C II M 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
