UNIVERSAL EP-60 通用环氧漆EP-60 属环氧漆。用于船舶压载舱或类似部位，可作为水下环境中的底漆使用。是一种低VOC 含量、高固体、双组份环氧厚浆涂料，用于浸水部位。本页参数：体积固体份 80 ± 2%、干膜厚度 100-300 微米/道、理论涂布率 0.354 千克/平方米/200 微米。同品牌同类可对比：EPOFEND AR 80 超强耐磨环氧厚浆漆、EPOFEND AR 耐磨环氧漆、EPOFEND MT-30 特种环氧漆MT-30。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 80 ± 2% |
|---|---|
| 干膜厚度 | 100-300 微米/道 |
| 理论涂布率 | 0.354 千克/平方米 /200 微米 |
| VOC | 190 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 30℃以上 |
| 稀释剂 | 环氧稀释剂#20 |
| 混合比 | Base/Hardener=9.44/1(by weight) |
| UNIVERSAL EP-60 | 通用环氧漆EP-60 |
|---|
A low VOC, high solids, two pack high build epoxy coating for immersed areas.
是一种低VOC 含量、高固体、双组份环氧厚浆涂料,用于浸水部位。
For ballast tank or similar location. As a primer for in-water service.
用于船舶压载舱或类似部位,可作为水下环境中的底漆使用。
Low VOC, High volume solids
低VOC 含量,高固体份
Excellent durability against crued oil, sea water
优秀的耐原油性、耐海水性
Resistance to cathodic protection
可承受阴极保护
High-build applicability
极好的厚涂施工性能
Good adhesion to bare steel substrates and a wide range of shop-primed surfaces.
同裸钢底材和大量的车间底漆都有良好的附着力。
| Color | Grey and Oxide Red |
|---|---|
| 颜色 | 灰色和铁红色 |
| Volume Solids 体积固体份 | 80±2 % |
| VOC | 190g/L,accord with EU Dircrtive2004/42/EC,subcategory j |
| 挥发性有机化合物含量 | 190 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| Flash Point | Greater than 30℃ |
| 闪点 | 30℃以上 |
| Film thickness | Dry : 100-300 microns/coat Wet : 125-375microns/coat |
| 涂装膜厚 | 干膜: 100-300 微米/道湿膜: 125-375 微米/道 |
| Theoretical Coverage | 0.354Kg/m2/200 microns |
| 理论涂覆率 | 0.354 千克/平方米/200 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理, 外界环境, 施工方法等多种因素有关。
| Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=9.44/1(by weight) |
| 混合比例 | 主剂/固化剂=9.44/1(质量比) |
| Pot life | 5℃ | 20℃ | 30℃ |
| 混合使用期 | 8hrs | 6hrs | 3hrs |
| Application Methods | Airless spray, air spray brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂和滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | 0.43mm-0.53mm |
| Nozzle pressure | 出口压力 | ≥15Mpa |
| Thinning ratio | 稀释比率 | 0-5% by volume(体积比) |
Brush/Roller 刷涂/滚涂 Thinning ratio 稀释比率 5-10% by volume(体积比)
| Thinner | Epomarine Thinner #20 |
|---|---|
| 稀释剂 | 环氧稀释剂#20 |
| Drying time & | Temperature | 温度 | 5℃ | 10℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 5hrs | 4hrs | 3hrs | 2hrs |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 48hrs | 24hrs | 16hrs | 12hrs |
| Min. interval | 最小涂装间隔 | 48hrs | 36hrs | 24hrs | 16hrs | |
| Max. interval | 最大涂装间隔 | 7days | ||||
| Typical undercoat | Bare steel, SD ZINC 500 etc. |
|---|---|
| 适用下涂 | 裸钢,环氧富锌涂料500 等 |
| Typical topcoat | RETAN 6000, KANPE FLON HD or according to the coating system of Cosco Kansai. |
| 适用上涂 | 聚氨酯面漆6000,氟碳面漆或参考我司涂装配套 |
Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.
Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非我方所 能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司产品及生产工艺 的不断发展,本说明书的内容也会随时进行更改,此中所有信息均以我方确认为主。产品 使用前,请确认所持说明书为最新版本。
| Issued Date | 2018/4 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI UNIVERSAL EP-60 通用环氧漆EP-60 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
