SD NON ZINC PRIMER 环氧无锌车间底漆 属富锌底漆。作为钢结构、集装箱的车间底漆、底漆使用。以环氧树脂为基料的无锌车间底漆。快干性能 Excellent compatibility with most kinds of subsequent coats 与各类面漆有极好的配套性 Less effect for gas cutting and welding properties 对气割和焊接性能影响较小 Strong adhesion to steel 与钢铁表面有良好的附着力。本页参数：干膜厚度 30-50 微米/道、理论涂布率 0.029 千克/平方米/10 微米、组份数 双组份。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | — |
|---|---|
| 干膜厚度 | 30-50 微米/道 |
| 理论涂布率 | 0.029 千克/平方米 /10 微米 |
| VOC | <500 克/升符合国标30981,溶剂型集装箱涂料 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 稀释剂 | SC ZINC PRIMER THINNER |
| 混合比 | Base /Hardener =6/1 (by wt.) |
| 颜色/外观 | 铁红或灰色 |
| SD NON ZINC PRIMER | 环氧无锌车间底漆 |
|---|
A zinc-free shop primer based on epoxy resin
以环氧树脂为基料的无锌车间底漆。
As shop primer or primer for steel structure, container
作为钢结构、集装箱的车间底漆、底漆使用
Complies with JT/T 810
符合JT/T 810《集装箱涂料标准》
Quick drying
快干性能
Excellent compatibility with most kinds of subsequent coats
与各类面漆有极好的配套性
Less effect for gas cutting and welding properties
对气割和焊接性能影响较小
Strong adhesion to steel
与钢铁表面有良好的附着力
| Color | Oxide red or Grey |
|---|---|
| 颜色 | 铁红或灰色 |
| Mixing ratio | Base /Hardener =6/1 (by wt.) |
| 混合比 | 主剂/固化剂=6/1(重量比) |
| VOC | <500 g/L accord with GB 30981-2020,solvent container paints |
| 挥发性有机化合物含量 | <500 克/升符合国标30981,溶剂型集装箱涂料 |
| Film thickness | Dry :30~50 microns/coat Wet:60~100 microns/coat |
| 涂装膜厚 | 干膜:30-50 微米/道湿膜:60-100 微米/道 |
| Theoretical Coverage | 0.029 kg/m²/10 microns |
| 理论涂布率 | 0.029 千克/平方米/10 微米 |
Practical:Variable on surface conditions, environment, applications method, etc.
实际涂布率与表面处理,外界环境,施工方法等多种因素有关。
| Application Temperature 施工温度 | 5℃-40℃ |
|---|
| Pot life | Temperature (℃) | 5 | 10 | 20 | 30 |
| 混合使用期 | Pot life (hrs) | 24 | 16 | 8 | 6 |
| Application Methods | Airless spray, air spray , brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂和滚涂 Airless spray 无气喷涂 |
| Nozzle tip size 喷嘴尺寸 | .019” ~ .023” |
| Nozzle pressure 出口压力 | 10~15 Mpa |
| Thinner 稀释剂 | SC ZINC PRIMER THINNER |
|---|
车间底漆稀释剂
| Drying time & Overcoating interval | Temperature | 5℃ | 20℃ | 30℃ | 80℃ |
| 干燥时间&涂装间隔 | Dry touch 表干 | 30mins | 15mins | 10mins | -- |
| Dry hard 半硬干 | 6hrs | 3hrs | 1hrs | 5mins | |
| Min interval 最小涂装间隔 | 20mins | 15mins | 3mins | ||
| Max interval 最大涂装间隔 | -- | ||||
| 涂装配套 Applied substrates | Bare steel |
|---|---|
| 适用底材 Subsequent coat | 裸钢 |
| 适用上涂 | Various of primers |
多种底漆
Store in dry, cool conditions, and away from sources of heat & ignition. Containers must be kept
tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12mouths/25℃ |
|---|---|
| 贮存期限 | 12 个月/25℃ |
Shelf life:Subject to re-inspection thereafter.
贮存期:以实际检验结果为准
| SURFACE REPARATION | Remove salt and other water-soluble contaminants by fresh water hosing. |
|---|---|
| 表面处理 | 用清水冲去盐份及其它水溶性污物。 |
Degrease according to SSPC-SP1 solvent cleaning.
依照SSPC-SP1 溶剂清洗标准除去油脂。
Remove rust, mill-scale and other loose material by abrasive blasting to ISO Sa2.5 (SSPC-SP10) or better.
用喷砂方式除去铁锈、氧化皮等达到ISO Sa2.5 (SSPC-SP10)或更好。
Remove dust and dirt by high pressure air before paint application
用高压空气吹扫除去灰尘等污物。
Be sure that the surface is clean and dry prior to application.
施工前确认表面清洁干燥。
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.
Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非我方所 能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司产品及生产工艺 的不断发展,本说明书的内容也会随时进行更改,此中所有信息均以我方确认为主。产品 使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | kansai.hk.coscoshipping.com |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI SD NON ZINC PRIMER 环氧无锌车间底漆 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
