SD MARINE BUILD PRIMER 醇酸厚涂底漆 属底漆。用于非浸没区域的钢结构表面。由长油醇酸树脂和防锈颜料组成的防锈底漆。良好的防腐性能 Compatibility with alkyd finish systems 可以同醇酸面漆配套 Good workability 良好的施工性能。本页参数：体积固体份 57 ± 2%、干膜厚度 50-100 微米/道、理论涂布率 11.4 平方米/升。同品牌同类可对比：ALKFEND PRIMER 30 醇酸底漆30、AMEINCOAT PRIMER、AMEINCOAT RC PRIMER。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 57 ± 2% |
|---|---|
| 干膜厚度 | 50-100 微米/道 |
| 理论涂布率 | 11.4 平方米/升 /50μm |
| VOC | — |
| 密度/比重 | — |
| 组份数 | 单组份 |
| 闪点 | 38℃以上 |
| 稀释剂 | 专用稀释剂 |
| 混合比 | 单组份涂料 |
| SD MARINE BUILD PRIMER | 醇酸厚涂底漆 |
|---|
A rust preventive primer based on long oil alkyd resin and anti-rust pigments.
由长油醇酸树脂和防锈颜料组成的防锈底漆
For steel structure in non immersion areas.
用于非浸没区域的钢结构表面。
Good corrosion resistance
良好的防腐性能
Compatibility with alkyd finish systems
可以同醇酸面漆配套
Good workability
良好的施工性能
| Color | Oxide Red, Grey |
|---|---|
| 颜色 | 铁红色,灰色 |
| Volume Solids 体积固体份 | 57±2% |
| Flash Point | Greater than 38℃ |
| 闪点 | 38℃以上 |
| Film thickness | Dry : 50-100 microns/coat Wet : 88-176microns/coat |
| 涂装膜厚 | 干膜: 50-100 微米/道湿膜:88-176 微米/道 |
| Theoretical Coverage | 11.4m2/Ltr/50 microns |
| 理论涂布率 | 11.4 平方米/升/50μm |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂布率与表面处理, 外界环境, 施工方法等多种因素有关。
| SURFACE PREPARATION | Remove salt and other water-soluble contaminants by fresh water. |
|---|---|
| 表面处理 | 用清水冲去盐份及其它水溶性污物。 |
Remove oil and grease with suitable detergent or solvent(SSPC-SP-1).
依照SSPC-SP1 溶剂清洗标准除去油脂。
Remove rust, mill-scale and other loose material completely by abrasive blasting.
用喷砂方式除去铁锈、氧化皮等达到ISO Sa21/2(SSPC-SP10)或更好。
All surface to be coated should completely clean,dry and free from contamination.
涂漆前确认表面清洁干燥无灰尘。
| Application Temperature 施工温度 | -5℃-40℃ |
|---|---|
| Mixing | Mix thoroughly with power agitator |
| 混合 | 使用动力工具搅拌均匀 |
| Mixing Ratio | One component coating |
| 混合比例 | 单组份涂料 |
| Application Methods | Airless spray, air spray, brush and roller |
| 施工方法 | 无气喷涂、空气喷涂、刷涂、滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | 0.43mm-0.53mm |
| Nozzle pressure | 出口压力 | ≥10Mpa |
| Thinning ratio | 稀释比率 | 0-10% by weight(重量比) |
Brush/Roller 刷涂、滚涂 Thinning ratio 稀释比率 0-10% by weight(重量比)
| Thinner | SD MARINE Paint Thinner |
|---|---|
| 稀释剂 | 专用稀释剂 |
| Drying time & Overcoating interval | Drying time & Surface dry | Drying time & 指触干燥 | -5℃ 4hrs | 5℃ 2hrs | 20℃ 1hr | 30℃ 30mins |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 16hrs | 10hrs | 6hrs | 4hr |
| Min. interval | 最小涂装间隔 | 36hrs | 24hrs | 10hrs | 8hrs | |
| Max. interval | 最大涂装间隔 |
| Applied substrates | Bare steel |
|---|---|
| 适用底材 | 裸钢 |
| Typical topcoat | SD MARINE BTD or according to the coating system of Cosco Kansai. |
| 适用上涂 | 醇酸面漆或参考我司涂装配套 |
Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非我方所 能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司产品及生产工艺 的不断发展,本说明书的内容也会随时进行更改,此中所有信息均以我方确认为主。产品 使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | 2025/1 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI SD MARINE BUILD PRIMER 醇酸厚涂底漆 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
