PU FINISH LD-50 聚氨酯面漆LD-50 属面漆。用于新建设施或作为维修保养面漆使用。A durable finish based on polyurethane.良好的施工性 Good adhesion to epoxy primers 同环氧涂料附着力良好 Quick drying 干燥迅速。本页参数：体积固体份 55 ± 2%、干膜厚度 40-60 微米/道、理论涂布率 11.0 平方米/升。同品牌同类可对比：AMEINCOAT INT、AMEINCOAT RC TOPCOAT、EPOMARINE AE-10 TOPCOAT 耐油导静电面漆。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 55 ± 2% |
|---|---|
| 干膜厚度 | 40-60 微米/道 |
| 理论涂布率 | 11.0 平方米/升 /50 微米 |
| VOC | 400g/L |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 23℃以上 |
| 稀释剂 | 聚氨酯稀释剂 |
| 混合比 | Base/Hardener=13/1(by weight) |
| PU FINISH LD-50 | 聚氨酯面漆LD-50 |
|---|
A durable finish based on polyurethane.
装饰性聚氨酯面漆。
As a finish can be used in new construction situations and as industrial maintenance finish
用于新建设施或作为维修保养面漆使用。
Complies with HG/T 2454-2014
符合HG/T 2454-2014《溶剂型聚氨酯涂料》
good application
良好的施工性
Good adhesion to epoxy primers
同环氧涂料附着力良好
Quick drying
干燥迅速
| Color | White and Colors |
|---|---|
| 颜色 | 白色及各色 |
| Gloss | Glossy |
| 光泽 | 亮光 |
| Volume Solids 体积固体份 | 55±2% |
| VOC | 400g/L |
| 挥发性有机化合物含量 | 400g/L |
| Flash Point | Greater than 23℃ |
| 闪点 | 23℃以上 |
| Film thickness | Dry :40-60microns/coat Wet : 73-110microns/coat |
| 涂装膜厚 | 干膜:40-60 微米/道湿膜: 73-110 微米/道 |
| Theoretical Coverage | 11.0m2/L/50 microns |
| 理论涂布率 | 11.0 平方米/升/50 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂布率与表面处理, 外界环境, 施工方法等多种因素有关。
| Application Temperature 施工温度 | -5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=13/1(by weight) |
| 混合比例 | 主剂/固化剂=13/1(质量比) |
| Pot Life | 5℃ | 10℃ | 20℃ | 30℃ |
| 混合使用期 | 6hrs | 5hrs | 3hrs | |
| Application Methods | Airless spray, air spray, brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂、滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | 0.33mm-0.43mm |
| Nozzle pressure | 出口压力 | ≥10Mpa |
| Thinning ratio | 稀释比率 | 5-15% by weight(重量比) |
Brush/Roller 刷涂、滚涂 Thinning ratio 稀释比率 5-15% by weight(重量比)
| Thinner | Retan Thinner |
|---|---|
| 稀释剂 | 聚氨酯稀释剂 |
| Drying time & | Temperature | 温度 | 5℃ | 10℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 2hrs | 1.5hrs | 1hr | 0.5hr |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 16hrs | 12hrs | 10hrs | 6hrs |
| Min. interval | 最小涂装间隔 | 24hrs | 20hrs | 16hrs | 12hrs | |
| Max. interval | 最大涂装间隔 | - | ||||
| Typical undercoat | Universal EP-60, Epotect EX or according to the coating systems of Cosco Kansai |
|---|---|
| 适用下涂 Typical topcoat 适用上涂 | Universal EP-60, Epotect EX 或参考我司推荐配套 |
Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非我方所 能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司产品及生产工艺 的不断发展,本说明书的内容也会随时进行更改,此中所有信息均以我方确认为主。产品 使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | 2025/07 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI PU FINISH LD-50 聚氨酯面漆LD-50 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
