PU FINISH LD-30 属面漆。用于新建设施或作为维修保养面漆使用。A high gloss durable finish based on polyurethane.良好的耐候性和保光性 Good application 良好的施工性 Dry-fast 干燥迅速。本页参数：体积固体份 54% ± 2%、理论涂布率 13.5 平方米/升、组份数 双组份。同品牌同类可对比：AMEINCOAT INT、AMEINCOAT RC TOPCOAT、EPOMARINE AE-10 TOPCOAT 耐油导静电面漆。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 54% ± 2% |
|---|---|
| 干膜厚度 | 30-60μm/道 |
| 理论涂布率 | 13.5 平方米/升 /40 微米 |
| VOC | 430 克/升 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 25℃以上 |
| 稀释剂 | 聚氨酯稀释剂2# |
| 混合比 | Base/Hardener=8/1(by weight) |
| PU FINISH LD-30 | 聚氨酯面漆LD-30 |
|---|
A high gloss durable finish based on polyurethane.
高光泽高性能聚氨酯面漆
As a finish can be used in new construction situations and l maintenance finish.
用于新建设施或作为维修保养面漆使用
Complies with HG/T 2454-2014
符合 HG/T 2454-2014 溶剂型聚氨酯涂料
Good weathering resistance and gloss retention
良好的耐候性和保光性
Good application
良好的施工性
Dry-fast
干燥迅速
| Color | White and Colors |
|---|---|
| 颜色 | 白色及各色 |
| Gloss | High gloss |
| 光泽 | 高光 |
| Volume Solids 体积固体份 | 54%±2% |
| VOC | 430g/L |
| 挥发性有机化合物含量 | 430 克/升 |
| Flash Point | Greater than 25℃ |
| 闪点 | 25℃以上 |
| Film thickness | Dry : 30-60μm /coat Wet : 55-110μm /coat |
| 涂装膜厚 | 干膜:30-60μm/道湿膜: 55-110μm/道 |
| Theoretical Coverage | 13.5m2/l/40μm |
| 理论涂布率 | 13.5 平方米/升/40 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理,外界环境,施工方法等多种因素有关
| Application Temperature 施工温度 | -5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=8/1(by weight) |
| 混合比例 | 主剂/固化剂=8/1(重量比) |
| Pot Life | 5℃ | 10℃ | 20℃ | 30℃ |
| 混合使用期 | 16hrs | 12hrs | 8hrs | 4hrs |
| Application Methods | Airless spray, air spray brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂和滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | 0.33mm-0.43mm |
| Nozzle pressure | 出口压力 | ≥10MPa |
| Thinning ratio | 稀释比率 | 15-30% by volume(体积比) |
Brush/Roller 刷涂/滚涂 Thinning ratio 稀释比率 15-30% by volume(体积比)
| Thinner | Retan Thinner 2# |
|---|---|
| 稀释剂 | 聚氨酯稀释剂2# |
| Drying time & | Temperature | 温度 | 5℃ | 10℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 表面干燥 | 100mins | 90mins | 60mins | 30mins |
| 干燥时间&涂装间隔 | Touch dry | 指触干燥 | 16hrs | 12hrs | 4hrs | 2hrs |
| Min. interval | 最小涂装间隔 | 24hrs | 20hrs | 8hrs | 4hrs | |
| Max. interval | 最大涂装间隔 | - | ||||
| Typical undercoat | Epomarine EX 600, Epofend Undercoat or according to the coating systems of COSCO |
|---|---|
| 适用下涂 | Kansai |
Epomarine EX 600,环氧中间漆或参考我司推荐涂装配套
Store in dry, cool condition and away from sources of heat and ignition. Containers
must be kept tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the
time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development. Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非 我方所能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司 产品及生产工艺的不断发展,本说明书的内容也会随时进行更改,此中所有信息 均以我方确认为主。产品使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | 2020/03 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI PU FINISH LD-30 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
