EPOTECT EX 发行日期 属环氧漆。用于新造船项目，可作为底漆或中间漆使用。是一种低VOC 含量、高固体、双组份厚浆型环氧涂料。本页参数：体积固体份 76 ± 2%、干膜厚度 75-200 微米/道、理论涂布率 6.08 平方米/升。同品牌同类可对比：EPOFEND AR 80 超强耐磨环氧厚浆漆、EPOFEND AR 耐磨环氧漆、EPOFEND MT-30 特种环氧漆MT-30。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 76 ± 2% |
|---|---|
| 干膜厚度 | 75-200 微米/道 |
| 理论涂布率 | 6.08 平方米/升 /125μm |
| VOC | 256/克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 20℃以上 |
| 稀释剂 | 30℃ |
| 混合比 | Base/Hardener=9/1(by weight) |
| 施工方法 | 无气喷涂、空气喷涂、刷涂和滚涂 Airless spray 无气喷涂 |
|---|
| Nozzle tip | 喷嘴尺寸 | 0.43mm-0.53mm |
| Nozzle pressure | 出口压力 | ≥15Mpa |
| Thinning ratio | 稀释比率 | 0-10% by volume(体积比) |
Brush/Roller 刷涂、滚涂 Thinning ratio 稀释比率 5-15% by volume(体积比)
Epomarine Thinner #20
| Thinner | 环氧稀释剂#20 |
|---|
| 稀释剂 | Temperature | 温度 | 5℃ | 10℃ | 20℃ | 30℃ |
| Drying time & | Surface dry | 指触干燥 | 5hrs | 4hrs | 3hrs | 2hrs |
| Overcoating interval | Touch dry | 半硬干燥 | 48hrs | 24hrs | 16hrs | 12hrs |
| 干燥时间&涂装间隔 | Min. interval | 最小涂装间隔 | 48hrs | 36hrs | 24hrs | 16hrs |
| Max. interval | 最大涂装间隔 | 7days | ||||
Bare steel
| Applied Substrate | 裸钢 |
|---|---|
| 适用底材 | SD Zinc 500, Epofend Zinc 60 etc. |
| Typical undercoat | 环氧富锌涂料500,环氧富锌60 等 |
| 适用下涂 | Retan 6000, Kanpe Flon HD or according to the coating system of COSCO Kansai. |
| Typical topcoat 适用上涂 | 聚氨酯面漆6000,氟碳面漆或参考我司涂装配套 |
Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非我方所能 控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司产品及生产工艺的不 断发展,本说明书的内容也会随时进行更改,此中所有信息均以我方确认为主。产品使用前, 请确认所持说明书为最新版本。
| ssued Date 发行日期 | 2024/12 |
|---|---|
| EPOTECT EX | 环氧漆 EX |
A low VOC, high solids, two pack high build epoxy coating
是一种低VOC 含量、高固体、双组份厚浆型环氧涂料。
As a primer or intermediate coat can be used in new building and repair vessel .
用于新造船项目,可作为底漆或中间漆使用。也可在修船项目中使用。
Low VOC, high volume solids
低VOC 含量,高固体份
Good anti-corrosive performance
极好的防腐性能
Excellent surface-tolerant properties
极好的表面适应性能
High-build applicability
极好的厚涂施工性能
Add MIO .(Micaceous Iron Oxide),can be overcoated after extended periods
添加云铁成分,适应较长时间后覆涂
| Color | Grey |
|---|---|
| 颜色 | 灰色 |
| Volume Solids 体积固体份 | 76±2% |
| VOC | 256g/L,accord with EU Dircrtive2004/42/EC,subcategory j |
| 挥发性有机化合物含量 | 256/克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| Flash Point | Greater than 20℃ |
| 闪点 | 20℃以上 |
| Film thickness | Dry : 75-200 μm/coat Wet : 98-263μm/coat |
| 涂装膜厚 | 干膜: 75-200 微米/道湿膜: 98-263 微米/道 |
| Theoretical Coverage | 6.08m2/Ltr/125 microns |
| 理论涂覆率 | 6.08 平方米/升/125μm |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理, 外界环境, 施工方法等多种因素有关。
| Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=9/1(by weight) |
| 混合比例 | 主剂/固化剂=9/1(质量比) |
| Pot life | 5℃ | 10℃ | 20℃ | 30℃ |
| 混合使用期 | 8hrs | 6hrs | 3hrs | |
| Application Methods | Airless spray, air spray, brush and roller |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI EPOTECT EX 发行日期 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
