EPOTAINER EX-600 环氧漆EX-600 属环氧漆。Corrosion Resistant suitable for UL 50E enclosures. 用于特殊要求的集装箱表面，可作为水下环境中的底漆使用。聚酰胺固化的厚涂型改性环氧涂料，可用于浸水部位。本页参数：干膜厚度 75-150 微米/道、理论涂布率 0.021 千克/平方米/10 微米、组份数 双组份。同品牌同类可对比：EPOFEND AR 80 超强耐磨环氧厚浆漆、EPOFEND AR 耐磨环氧漆、EPOFEND MT-30 特种环氧漆MT-30。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 65% |
|---|---|
| 干膜厚度 | 75-150 微米/道 |
| 理论涂布率 | 0.021 千克/平方米 /10 微米 |
| VOC | 340 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 20℃以上 |
| 稀释剂 | 环氧稀释剂#20 |
| 混合比 | Base/Hardener=7/1(by weight) |
| EPOTAINER EX-600 | 环氧漆EX-600 |
|---|
A high-build polyamide cured modified epoxy coating suitable for immersed areas.
聚酰胺固化的厚涂型改性环氧涂料,可用于浸水部位。
For container with special requirements. As a primer for in-water service. Outdoor
Corrosion Resistant suitable for UL 50E enclosures.
用于特殊要求的集装箱表面,可作为水下环境中的底漆使用。可用作UL50E 外壳 户外防腐。
Excellent durability against cured oils, sea water
优秀的耐原油性、耐海水性
Resistance to cathodic protection
可承受阴极保护
High-build applicability
极好的厚涂施工性能
Good adhesion to bare steel substrates and a wide range of shop-primed surfaces
同裸钢底材和大量的车间底漆都有良好的附着力。
Lead free*, be friendly with health and environment
无铅,有益于健康和环境
*:Lead free is defined in order to comply with the request of JIS K 5674
*:无铅的概念为满足JIS K 5674 中对铅含量的要求
UL50E certified
通过UL50E 认证
| Color | Grey and Oxide Red |
|---|---|
| 颜色 | 灰色和铁红色 |
| Volume Solids | 65% |
| 体积固体份 | 340g/L,accord with EU Dircrtive2004/42/EC,subcategory j |
| VOC | 340 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 挥发性有机化合物含量 | Greater than 20℃ |
| Flash Point 闪点 | 20℃以上 |
| Film thickness | Dry 75-150 microns/coat Wet : 115-230microns/coat |
| 涂装膜厚 | 干膜: 75-150 微米/道湿膜: 115-230 微米/道 |
| Theoretical Coverage | 0.021Kg/m2/10microns |
| 理论涂覆率 | 0.021 千克/平方米/10 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理, 外界环境, 施工方法等多种因素有关。
| Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=7/1(by weight) |
| 混合比例 | 主剂/固化剂=7/1(重量比) |
| Pot life | 10℃ | 20℃ | 30℃ |
| 混合使用期 | 12hrs | 8hrs | |
| Application Methods | Airless spray, air spray , brush and roller |
|---|---|
| 施工方法 | 无气喷涂、空气喷涂、刷涂和滚涂 Airless spray 无气喷涂 |
| Nozzle tip | 喷嘴尺寸 | 0.43mm-0.53mm |
| Nozzle pressure | 出口压力 | ≥10Mpa |
| Thinning ratio | 稀释比率 | 0-5% by volume(体积比) |
Brush/Roller 刷涂、滚涂 Thinning ratio 稀释比率 5-10% by volume(体积比)
| Thinner | Epomarine Thinner #20 |
|---|---|
| 稀释剂 | 环氧稀释剂#20 |
| Drying time & | Temperature | 温度 | 10℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 3hrs | 1hr | 30mins |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 24hrs | 16hrs | 12hrs |
| Before flooding | 耐浸干燥 | 7days | |||
| Min. interval | 最小涂装间隔 | 24hrs | 16hrs | 12hrs | |
| Max. interval | 最大涂装间隔 | 7days | |||
| Typical undercoat | Bare steel, EPOTAINER ZINC 60 etc. |
|---|---|
| 适用下涂 | 裸钢,环氧富锌底漆60 等 |
| Typical topcoat | PU FINISH CT-50, or according to the coating system of Cosco Kansai. |
| 适用上涂 | 聚氨酯面漆CT-50,或参考我司涂装配套 |
Store in dry, cool condition and away from sources of heat and ignition. Containers must
be kept tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the
time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非 我方所能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司 产品及生产工艺的不断发展,本说明书的内容也会随时进行更改,此中所有信息 均以我方确认为主。产品使用前,请确认所持说明书为最新版本。
| Issued Date | 2023/9 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI EPOTAINER EX-600 环氧漆EX-600 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
