EPOMARINE PC-100 环氧漆PC-100 属环氧漆。作为底面合一涂料用于成品油舱。A two pack hi-build epoxy tank coating.本页参数：体积固体份 49 ± 2%、干膜厚度 75-150 微米/道、理论涂布率 4.9 平方米/升。同品牌同类可对比：EPOFEND AR 80 超强耐磨环氧厚浆漆、EPOFEND AR 耐磨环氧漆、EPOFEND MT-30 特种环氧漆MT-30。
以上内容整理自原厂说明书与本站参数表；选型、配套与货期请联系我们确认。
| 体积固体份 | 49 ± 2% |
|---|---|
| 干膜厚度 | 75-150 微米/道 |
| 理论涂布率 | 4.9 平方米/升 /100 微米 |
| VOC | 440 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| 密度/比重 | — |
| 组份数 | 双组份 |
| 闪点 | 20℃以上 |
| 稀释剂 | 环氧稀释剂 |
| 混合比 | Base/Hardener=4/1(by weight) |
| EPOMARINE PC-100 | 环氧漆PC-100 |
|---|
A two pack hi-build epoxy tank coating.
是一种厚浆型环氧储罐涂料。
As a protective primer-finish coat can be used in product oil tanks.
作为底面合一涂料用于成品油舱。
Remarkable resistance to crude oil, petroleum products, aliphatic solvents, salt water and a broad
range of chemicals
良好的耐原油、石油、脂肪烃溶剂性能和耐盐水性,同时对多种化学药品有良好的耐受性
Excellent high-build applicability
极好的厚涂施工性能
Excellent anti-abrasion and impact resistance
极好的耐磨损和耐冲击性能
| Color | Grey , White and Pink |
|---|---|
| 颜色 | 灰色,白色和粉色 |
| Volume Solids 体积固体份 | 49±2% |
| VOC | 440g/L,accord with EU Dircrtive2004/42/EC,subcategory j |
| 挥发性有机化合物含量 | 440 克/升,符合欧盟溶剂排放指令2004/42/EC,j 子类别 |
| Flash Point | Greater than 20℃ |
| 闪点 | 20℃以上 |
| Film thickness | Dry 75-150 microns/coat Wet : 153-306microns/coat |
| 涂装膜厚 | 干膜: 75-150 微米/道湿膜: 153-306 微米/道 |
| Theoretical Coverage | 4.9 m2/L/100microns |
| 理论涂覆率 | 4.9 平方米/升/100 微米 |
Practical coverage depending on surface conditions, environment, applications, etc.
实际涂覆率与表面处理, 外界环境, 施工方法等多种因素有关。
| 施工 Application Temperature 施工温度 | 5℃-40℃ |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| 混合 | 混合主剂与固化剂,使用动力工具搅拌均匀 |
| Mixing Ratio | Base/Hardener=4/1(by weight) |
| 混合比例 | 主剂/固化剂=4/1(质量比) |
| Pot life | 5℃ | 20℃ | 30℃ |
| 混合使用期 | 12hrs | 8hrs | 5hrs |
| Application Methods 施工方法 | Airless spray, air spray, brush and roller |
|---|
无气喷涂、空气喷涂、刷涂、滚涂 Airless spray 无气喷涂
| Nozzle tip | 喷嘴尺寸 | 0.43mm-0.53mm |
| Nozzle pressure | 出口压力 | ≥10Mpa |
| Thinning ratio | 稀释比率 | 0-5% by volume(体积比) |
Brush/Roller 刷涂/滚涂 Thinning ratio 稀释比率 5-10% by volume(体积比)
| Thinner | Epomarine Thinner |
|---|---|
| 稀释剂 | 环氧稀释剂 |
| Drying time & | Temperature | 温度 | 5℃ | 20℃ | 30℃ |
| Overcoating interval | Surface dry | 指触干燥 | 3hrs | 2hrs | 1hr |
| 干燥时间&涂装间隔 | Touch dry | 半硬干燥 | 48hrs | 16hrs | 12hrs |
| Min. interval | 最小涂装间隔 | 48hrs | 16hrs | ||
| Max. interval | 最大涂装间隔 | 14days | 7days | ||
| Applied Substrate | Bare steel |
|---|---|
| 适用下底材 | 裸钢 |
| Typical topcoat | EPOMARINE PC-100 |
| 适用上涂 | 环氧漆PC-100 |
Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed.
贮存于干燥阴凉的环境中,远离热源及火源。包装桶必须保持封闭。
| Shelf life | 12 months from date of production (25℃) |
|---|---|
| 贮存期限 | 自生产之日起12 个月(25℃) |
The information given on this sheet is to the best of our knowledge and accurate at the time of
issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本说明书所提供信息均为目前我方所掌握最全面正确的资料,鉴于产品使用条件非我方所 能控制,此中信息不含担保,即仅在选取产品上对买方负责。由于我公司产品及生产工艺 的不断发展,本说明书的内容也会随时进行更改,此中所有信息均以我方确认为主。产品 使用前,请确认所持说明书为最新版本。
| Issued Date 发行日期 | 2024/10 |
|---|
资料以厂商最新版为准，具体以原厂最新 TDS 为准。查看 关西 KANSAI EPOMARINE PC-100 环氧漆PC-100 原厂 PDF 说明书全文。
原厂包装规格与批次交期以实际供货为准，可联系我们按项目核算。
